图片
图片
图片
文章正文
XINTAO 5A Molecular Sieve for VPSA Oxygen Concentration 95.6%
2023-07-31 14:44:37   
1. Oxygen generator equipment type: VPSA

2. Installation location/time: China. 2022.07.03

3. Tower diameter (inside): 2.68m Height: 6.5m

4. Loading capacity: (1) A total of 14 tons of 5A oxygen production Molecular sieve, 7 tons/tower (2) 2.5 tons of activated alumina, 1 ton/tower

5. The main technical performance requirements of the customer: Oxygen flow rate 350Nm³/Hr Oxygen concentration ≥ 93%±2%

After installing Xintao oxygen molecular sieve, the flow rate is 340 -380Nm³/Hr Oxygen concentration 95.6%

6. Requirements for the purchase of screens and cotton cloth:

(1) Requirements for 304 stainless steel wire mesh: Tower diameter (mm) X4 (4 pieces in total, 2 towers, 2 pieces for each tower, one piece for the upper layer and one piece for the bottom layer)

(2) Requirements for non-woven cotton: Tower diameter (mm) X4 (total 4 pieces, 2 towers, 2 pieces for each tower, one piece for the upper layer and one piece for the bottom layer)

VPSA is vacuum desorption:
 Vacuum pressure swing adsorption (VPSA for short) oxygen production equipment, that is, under the condition of penetrating atmospheric pressure, special molecular sieves are used to selectively adsorb nitrogen, carbon dioxide and water in the air. Molecular sieves are desorbed to circulate high-purity oxygen (90-95.6%). The VPSA consumes less energy, and the larger the device, the lower the energy consumption.

The air enters the blower through the filter, and is conveyed by the blower from the adsorption tower department enters. The lower part of the adsorption tower is filled with activated alumina. The function of activated alumina is to remove moisture, carbon dioxide and a small amount of other gases in the air, so as not to "poison" the 5A molecular sieve. The upper part of the adsorption tower is a 5A molecular sieve. When the air flows through the filled molecular sieve fixed bed,the oxygen molecular sieve in the air diffuses into the molecular sieve solid under the adsorption force, and the oxygen molecules pass through the bed to the buffer tank. The buffer tank is connected with the oxygen compressor to compress the product to the pressure required by the user and send it to the gas storage tank for production use.

After a period of adsorption, the molecular sieve particles are filled with nitrogen molecules and reach the adsorption saturation stage. At this time, close the air inlet valve, use the oxygen-enriched air in the tower to flush the other tower that has just been vacuumed, and close the pressure equalization after the pressure drops. At the same time, open the inlet valve of the vacuum pump to evacuate the tower body. After reaching a certain degree of vacuum, use part of the oxygen in the buffer tank of the oxygen-enriched machine in another tower to flush the molecular sieve, so that the adsorbent can be completely desorbed.

 

Each adsorber of VPSA performs the following steps alternately: Adsorption -------- Vacuum desorption ----- Stamping


(2) The difference between PSA and VPSA

The pressure of PSA oxygen generator is generally 0.5-0.8MPa, and the adsorption pressure of VPSA is 0.05MPA, which is less than 1/10 of that of PSA oxygen generator. The most important thing is that VPSA has lower energy consumption, is more environmentally friendly and green.

脚注信息


Copyright 2016 XINTAO Network Studio  All Rights Reserved 网站备案:赣ICP备12002161号-1

Address: West section, Hi-Tech Industrial Park, Pingxiang, Jiangxi 337000 China Tel:+86-799-6611966 Email:info@xt988.com

Built By AYZX

After-sales phone:0799-6611190


访问统计
自定内容

Friendly link: chemxin